Beakers   (PW - 6001)

Polylab Beakers, moulded in Polypropylene, have excellent clarity and very good chemical resistance. These autoclavablc Beakers have prominently raised graduations on the outer surface. Pouring a solution becomes very convenient because of its tapered spout.
Available in 50 Ml, 100ml, 250 ml, 500 ml 1000 ml & 2000 ml

Burette   (PW - 6002)

This Burette has a transparent acrylic body and a leakproof stopcock made fitted with a self lubricating PTFE plug. Each Burette is individually calibrated to give maximum accuracy. Acrylic body is unaffected by dilute mineral acids & bases except Hydrofloric Acid & Ammonium Hydroxide. The pH range of 1-14 is ideal and can be used up to 5% wt/wt of acids or 30% bases.

Material: Polymethyl Methacrylate/TPX
Available in25ml, 50 Ml, 100ml

Pipette Pump   (PW - 6003)

This pipette pump is fast release pipetting device for precise pipetting zip quick emptying. The Knurled thumbwheel can be rotated to draw up or dispense liquids while the releaser may be pushed in for zip-quii emptying. The moulded chuck has a silicon rubber collet inside to hold various pipettes of standard sizes. It resists acids & alkalies and can 1 easily disassembled for thorough cleaning.

Material: Acrylonitrile Butadiene Styrene
Available in: 2 m, 10 ml, 25 ml

Dropping Bottles   (PW - 6004)

Blown in Low Density Polyethylene, Polylab Dropping Bottles dispense small uniform drops of liquids when pressed lightly.

Material: Low Density Polyethylene
Available in: 60 ml, 125 ml

Reagent Bottles (Narrow Mount)   (PW - 6005)

These Narrow Mouth Reagent Bottles are available in Polypropylene as well as Polyethylene. The PP bottles are rigid, translucent and have excellent contact clarity. These bottles can be autoclaved filled as well as empty. On the other hand, the Polyethylene bottles too have excellent strength and are unbreakable. The Polypropylene Cap has a built in seal ring to make these bottles leakproof.

Material: Low Density Polyethylene & Polypropylene
Available in 60ml, 125ml, 250ml, 500ml, 1000ml

Reagent Bottles (Wide Mouth)   (PW - 6006)

Same as above but in Wide Mouth.
Available in 60ml, 125ml, 250ml, 500ml, 1000ml

Narrow Mouth Bottle   (PW - 6007)

This autoclavable bottle, made of polypropylene, can be used for storing & transfering chemicals and other reagents safe & sound.
Material: Polypropylene
Capacity: 4000ml

Wide Mouth Square Bottles   (PW - 6008)

This autoclavable bottle, made of polypropylene, can be used for storing & shipping chemicals & reagents. Being wide mouthed, it is always convenient to pour in &i take out the reagents. The built in depressions on two sides provide excellent grip while holding this bottle.
Material: Polypropylene
Capacity: 4000ml

Heavy Duty Vaccum Bottle   (PW - 6009)

This autoclavable bottle, made of polypropylene, has thick walls, is rugged & can be used for repeated applications of vaccum.
Material: Polypropylene
Capacity: 2000ml

Carboy With Stop Cock   (PW - 6010)

Adding in line of Polylab Aspirators, these polypropylene Carboys are autoclavable, dependable & durable. These are also equipped with a leak proof spigot screwed to the body. These carboys are an excellent replacement for glass carboys and arc used for storing & dispensing distilled water & other laboratory solutions.
Material: Polypropylene
Capacity: 10 ltr., 20 ltr.

Aspirator Bottles   (PW - 6011)

Polylab Aspirator Bottles are made of Polypropylene and are therefore much lighter than glass. These are autoclavable, durable & dependable. The leakproof spigot screwed to the bottle body requires only a half turn to open or close. These bottles are used for storing or dispensing distilled water & other laboratory solutions. Threads should be totally disengaged before autoclaving.
Material: Polypropylene
Capacity: 5 ltr., 10 ltr., 20 ltr.

Wash Bottles   (PW - 6012)

Polylab Wash Bottles are made of Low Density Polyethylene which gives these bottles a translucent & unbreakable character. Solutions can be poured easily by squeezing the bottle lightly. The cap is fitted with a flexible polyethylene delivery tube which can be aimed wherever required.
Material: Polyethylene
Capacity: 125ml, 250ml, 500ml, 1000ml

Conical Flask   (PW - 6013)

Made of Polypropylene, these cone shaped flasks are rigid, translucent & autoclavable. The screw cap keeps the contents of the flask contamination free and makes the flask leakproof. Threads should be disengaged before autoclaving.
Material: Polypropylene
Capacity: 100ml, 250ml, 500ml

Specimen Jar (Gas Jar)   (PW - 6014)

These transparent Specimen Jars, used for preserving different specimens in the lab are provided with a cap that fits in tight. These jars provided excellent protection to the species preserved in it.
Material: Polystyrene

Fisher Clamp   (PW - 6015)

These Clamps are moulded in Polypropylene making it completely corrosion-proof. The spring loaded jack in the middle provides a vice like grip to the Burette and prevents it from slipping. Two tapered wedges are provided to ensure firm grip on rods havingdia 1 /2"or 3/8".

Material: Polypropyletie
Availabel in Single and Double Type